It would be difficult to find a home that a quality paint job couldn’t enhance. But all paint works need routine upkeep, not to mention good prepping before the painting even starts, to keep them looking fresh for a long time. A relatively new home may experience paint difficulties, but older homes that are more susceptible to these issues. Everything has a shelf life, therefore the paint in a more aged home will eventually need to be replaced.

Some decorative problems, such as peeling paint or cracked plaster, might be difficult to solve, especially if you’re in the middle of a significant DIY undertaking. We have listed the most frequent paint issues and how to remedy them so you can spruce up your house like a pro. Make careful you read them before picking up a paintbrush if you’re about to do so.

1. Chalking
Loose-based powder known as “chalking” develops on painted walls. This prevalent paint issue is caused by low-quality paints that contain a lot of pigment extenders. The age, color, or method of painting are additional important considerations. Some colors that are highly tinted or extremely bright might rapidly turn chalky. Another issue that could arise is excessively thinned paint.

SOLUTION:
Scraping will get rid of the stray paint. Repaint damaged areas and fill in bare patches. Apply premium paints according to the advised spreading and thinning rates. It is best to use the highest-quality paint you can when employing vivid colors. Watch out for your paint job.

2. Blistering
This is blistering if you see bubbles emerging from the wall paint’s underlying layer. The moisture that is pulled away from the surface where the paint is applied results in blisters. It can be brought on by painting during periods of excessive humidity, painting a damp surface, or repainting too soon. The likelihood of blisters is further increased by inadequate surface preparation.

SOLUTION:
Avoid painting in conditions of high dew point or high humidity. Before applying paint, make sure the surface is dry and free of moisture. Prior to reapplying the paint, give the surface enough time to cure. Moisture becomes an issue if the blisters penetrate the skin’s surface. It is highly advised in this situation to install vents and exhaust fans in the affected areas. Your best chance of success—and perhaps the difference between success and failure—lies in selecting the appropriate primer undercoat for the type of surface to be painted.

3. Mould/Mildew
A fungus called mold/mildew is recognized by the surface growth of patches that are black, grey, brown, and green in color. In places with a lot of moisture, poor ventilation, and little sunlight, mold, and mildew like to thrive. Lack of/inadequate microbial shield in low-quality paint (which prevents mold and mildew) increases the likelihood of growth.

SOLUTION:
To eliminate mold spores, scrub the afflicted area with household white vinegar. Put a layer of stain-repellent primer on. To ensure proper ventilation, stay away from using cheap acrylic or oil-based alkyd paint and install exhaust fans in high-moisture regions.

4. Cracking/Crazing
A dried paint film separating through at least one coat is what defines cracking. It’s also possible that the first coat wasn’t totally dry when the second coat was applied.

SOLUTION:
Before repainting with high-quality paint at the prescribed spreading rate, sand the damaged area with fine-mesh sandpaper and apply the proper primer layer.

5. Yellowing
Yellowing can be caused by the oxidation of alkyd or oil-based paint or varnish, heat from household items like stoves and heaters, or a lack of light in the area.

SOLUTION:
Although low-sunlight locations tend to be yellow, it is recommended to steer clear of using alkyd or oil-based paint there. Acrylic paints work best under the aforementioned circumstances.

6. Peeling
The very typical paint issue known as peeling is characterized by the separation of an outer paint layer from an earlier paint layer. Lack of adhesion between a coating and a substrate, excessive wetness, or painting a dirty or dusty wall directly can all contribute to this problem.

SOLUTION:
Sand the impacted parts to make them smooth after scraping off the flaking paint. Apply a quality undercoat or sealer. Use only premium paint when you repaint.

7. Shriveling or Wrinkling
When the paint is applied too liberally or a second coat is placed before the previous one has had time to cure completely, the painted surface develops a skin that looks wrinkled or shriveled. Uncured paint exposed to moisture from rain, dew, and excessive humidity may also shrivel or wrinkle.

SOLUTION:
The base coat of a paint job needs to dry completely before the final coat is applied, which takes time. If you’re painting in hot, cool, or moist weather, give the drying process more time. Additionally, paint needs to be applied uniformly. For spreading rate and environmental circumstances, go per the manufacturer’s guidelines.

These common paint issues are caused by either a lack of diligence on the part of the individual who completed the work or a lack of familiarity with the paint supplies. After a while, repainting maintenance is frequently anticipated. Avoidance is preferable to cure.

Trust Smith Plastering with Your Next Painting Projects
All paints contain a variety of chemicals that will deteriorate over time. Therefore, it is normal for restoration or repainting to become necessary after a while. If you experience any of these paint issues too frequently, you should be concerned.

Prevent these common painting issues by hiring seasoned and reputable painters to finish the job! Hire our skilled painters so they can successfully complete a variety of commercial and residential painting projects.

To learn more about painting services, contact Smith Plastering at 239-594-7537, or message us online today!